Back to Blog
How-to Guides 2026-11-13 RPM TESLA ACCESSORIES – RPM TESLA Aftermarket 0 views

Model X GT Style Mirror Cap Covers: Install and Care Tips

Model X GT Style Mirror Cap Covers: Install and Care Tips

A practical guide to fitting GT Style real dry carbon fiber mirror overlays on your Model X, choosing gloss or matte, and protecting them from sun yellowing.

What these overlays are and who they suit

The GT Style Side View Mirror Overlay Cap Covers are a pair of real dry molded carbon fiber shells that sit over your Model X's original painted mirror skull. They fit all Model Xs made from 2016 to present, and the front rolled leading edge is fully covered with carbon fiber curled rolled edges. If you want an aggressive, sporty look without replacing the mirror housing, this is the part to consider.

They come in two finishes: Glossy (wet look) and Matte (dry look). Both are made from real dry molded carbon fiber, so the weave is visible and the surface has the depth you expect from carbon. The overlays install in about 15 minutes according to the product information, but the preparation and care steps below matter more than the speed of fitting.

Fitment and finish facts

Installation: prepare, test-fit, then bond

  1. Inspect and test-fit before removing any adhesive liner: Once the double-sided adhesive liner is removed, the product is considered used and cannot be returned. Check the weave, finish, and fit against your mirror skull first. The product information notes that carbon fiber patterns may show inconsistencies in direction and gaps between rows over curved surfaces; these variations are normal and not a manufacturer's defect.
  2. Clean the mirror skull surface: The supplied information does not list a specific cleaner or preparation chemical. Use a clean, dry surface and follow any general surface-prep guidance you trust; avoid anything that leaves residue. Do not skip this step, because adhesive performance depends on a clean surface.
  3. Remove the adhesive liner and position the overlay: The overlays slide right over the original painted mirror skull. Align the front rolled leading edge first, then press the rest into place. The product page states installation takes about 15 minutes and refers to a video for guidance; watch that video before you start if you want a visual reference.
  4. Press firmly and check edges: Work around the perimeter to seat the adhesive. The front rolled leading edge is designed to be completely covered with carbon fiber, so make sure it sits flush. The supplied information does not specify a curing time or temperature, so avoid washing or disturbing the mirrors immediately after fitting.

Glossy or matte: a quick decision

Choose Glossy (wet look) if you want the carbon weave to read as deep and reflective, closer to a painted or lacquered finish. Choose Matte (dry look) if you prefer a subtler, more technical appearance that blends with satin or matte trim. Both are real dry molded carbon fiber, so the difference is surface treatment, not material quality.

There is no functional advantage to either finish in the supplied information. The decision is visual. If you are unsure, look at the other carbon pieces on your Model X and match the sheen rather than mixing gloss and matte on adjacent parts.

Care that prevents yellowing and wear

  • Protect the clear coat from the start: The overlays come with three coats of UV protection infused in the epoxy resin, but the product information warns that this protection can wear off over time without waxing, clear bra PPF film, or a nano-ceramic coating. Apply one of these protective measures if the car is parked outside.
  • Watch for yellowing if the car lives outdoors: Prolonged direct sunlight can cause yellowing oxidation within a few months of installation when the car is not garaged. This natural discoloration is not covered under any warranty. Using a car cover, as the product information recommends, helps reduce sun exposure.
  • Address gloss yellowing with compound or wet sanding: For glossy carbon fiber, the yellowed top layer can be removed with compound and/or wet sanding. After the top epoxy layer is removed, the yellow oxidation is gone and the product can be polished to a bright, shiny finish. This is a gloss-specific remedy; the supplied information does not describe the same process for matte.
  • Know the warranty boundaries: The carbon fiber products carry a limited 1 Year Warranty. Weave pattern inconsistencies are considered normal variation, and yellowing oxidation from sun exposure is not covered. Keep this in mind when deciding how much protection to add.

Care and warranty evidence

Removal and adhesive notes

The supplied information does not describe a removal procedure or a specific adhesive remover. If you need to remove the overlays later, avoid harsh solvents that could damage the carbon fiber or the original mirror paint. Because the product is considered used once the adhesive liner is removed, removal is not a return path; it is a modification you should undertake only if you are prepared to reinstall or replace the overlays.

For returns before installation, keep the adhesive liner intact and inspect the product thoroughly. The return policy applies only to unused products, so test-fit without peeling the liner.

Related Articles

Customer Service
Home
Products
Cart
Profile